Questions tagged [hp-smart-array]
"Smart Array" is the name used by Hewlett-Packard's line of enterprise-grade RAID controllers.
504 questions
5 votes
1 answer
341 views
What HP Smart Storage Adminstrator CLI tool needed for HPE Smart Array P440ar Controller?
I have a HPE Smart Array P440ar Controller at AlmaLinux 9.6 and I need to monitor its indicators. I've installed hpssacli-2.40-13.0.x86_64 but get APPLICATION UPGRADE REQUIRED: This controller has ...
- 89
1 vote
1 answer
242 views
HP ProLiant DL380 Gen9 fails to start due to failed Smart Storage battery? [closed]
We have an HP ProLiant DL380 Gen9 running Ubuntu 18.04 (which previously ran Ubuntu 16.04). The update process itself went relatively smoothly. After rebooting, I was presented with a Red Screen of ...
- 111
6 votes
2 answers
1k views
HPE Smart Array P408i 2GB experiencing a performance drop
I have two HP ProLiant ML 350 GEN 10 with a RAID 10 SSD Samsung disks and HPE SmartArray P408 with 2 GB cache. It has good performance: When copying large files, performance drops after two minutes......
0 votes
3 answers
2k views
HP DL360 Gen9: Smart Storage Administrator hangs loading config from P440ar; BIOS sees P440ar controller, but no disks
I have been scanning the entire web (or so) for possible similar cases, but to no avail. Situation: DL360 Gen9, BIOS version P89 v2.92 (2021) P440ar installed, firmware 7.20 the (F9) System ...
- 1
2 votes
3 answers
6k views
Smart Array P420i, Logical Drive failed, best way to re-enable
I have a HP Proliant ML380p Gen8 server with a P420i controller where one of the logical drives suddenly failed. From what I could see in the Smart Storage Administrator, none of the physical drives ...
- 121
0 votes
0 answers
83 views
Smart array P212 error code 727
We recently purchased HP DL380P GEN8 server and D3700 enclosure with 20TB of disks. I wanted to connect both servers with Smart Array P212 but I encountered and error once I tried to configure the ...
- 1
0 votes
0 answers
280 views
install disks with raid on a controller of the same model? without losing data. hp dl160 g9 - b140i
I have an HP DL160 Gen 9 server with 4 disk drives, 2 HDD with RAID 1 and 2 SSD with RAID 1. This server is restarting repeatedly when the esxi System boots. If I install these 4 disks on an identical ...
-1 votes
1 answer
2k views
How to replace a hard disk in SMART array 410i controller, RAID 1 + 0
I have a HP ProLiant DL360 G7 server (ILO3). Recently I have been receiving a SMART error message related to drivers. When checked The Array configuration it was found that, There are total 8 disks. ...
5 votes
1 answer
987 views
HP Smart Array P812 HBA mode Masked Drives
I have an HP Smart Array P812 card flashed to HBA mode. Kernel patched Linux for this module, Ubuntu 22. Everything was working a week ago, I had passthrough of the drives, I even used them to test ...
- 75
4 votes
1 answer
1k views
HPE Smart Array P410 - Replacing failed drive of a degraded mirror with a new one using ssacli with the failed drive kept connected?
A server is using attached drives without the HP hot-plug drive cage, with drives attached to P410 using two SFF8087 -> 4x SAS SFF8482 cables. I can add new drives while running, but cannot remove ...
- 71
3 votes
1 answer
130 views
Increasing RAID1 (mirror) redundancy in HP Smart Array P410?
Please is it possible to add a third (or more) drives to a mirror (RAID1) in P410? IIUC it would mean creating "Mirror Group 3" (or more). I could not find any way to add a new mirror group ...
- 71
6 votes
1 answer
3k views
HP Smart Array B140i S2D
I try to create a S2D with my HP DL380 Smart Array B140i. I have all bays with SSDs and want to use bays 5-8 for a S2D. I need to configure the array controllor (or the BIOS?) to make the drives ...
- 63
0 votes
1 answer
1k views
HP DL360 Gen 8 not recognizing SSDs
I have HP DL360 Gen 8 Server with P420i controller. I've populated it with 4x1TB HDDs and 2x1TB SSDs. HDDs are recognized correctly and they are visible in controller configuration tool (smart array), ...
1 vote
0 answers
4k views
How to force array rebuild on HP smart array (ssacli)
i recently replaced a failed drive on my HW RAID 5 array in my home server. i am running a custom built machine (read: built from whatever parts i thought might fit together). the HW RAID controller ...
- 21
2 votes
2 answers
2k views
HP SmartArray: how to extend a fully populated RAID1+0
I have a bunch of machines with HPE Smart Array P408i-a controllers and fully populated drive bays, and I was wondering if there is a way to extend the arrays without dissolving them and reinstalling ...
- 43
-2 votes
2 answers
475 views
Increase server's logical drive support
I have an HPE ProLiant DL360p Gen8 Server, with one P420i controller. As I read in its specification, the controller's limit is 2 logical drives. What part(s) should I buy in order to increase it to 8 ...
0 votes
2 answers
2k views
Acessing HP Disk Array from Linux
I have some old HP Proliant GL5 with HP P400i array controllers that I want to put to some use. In a small test I have booted with Archlinux, and it was able to list the array card and network ...
- 109
-1 votes
2 answers
2k views
RAID performance with 10xSSD on an HP P420i [closed]
I am planning to use 10x 8TB Samsung 870 QVO SATA III 2.5" SSD in an HP DL360 G8 server that uses P420i smart array controller. Each SSD has a max of 530 MBs speed in sequential reads. ...
- 111
1 vote
1 answer
427 views
HP ML350 Replacing a Drive Marked as Predicted to Fail
We have an ML350P Gen8 server with an HP Smart Array P420i. Three 300GB drives are combined in RAID5. Of these, one drive is showing a flashing amber light (predictive failure). The cache for the ...
- 161
0 votes
1 answer
574 views
Cabling for SAS controller and SuperMicro BPN-SAS-825TQ
I´ve managed to get one of the SuperMicro low-end server to my lab. It is chassis 825TQ-R740LPB with a BPN-SAS-825TQ backplane. The specification document is saying, that this backplane is SAS ...
0 votes
0 answers
532 views
Linux doesn't boot when HP HBA controller is connected
I have an HP H240 Smart HBA. On Windows 10, it works without a problem, but any Linux I tested refuses to boot with a connected controller. Platform: AMD B450 (AM4, various processors) List of tested ...
- 1
2 votes
0 answers
844 views
Can we move the RAID array from one HP Server models to another HP models or one RAID controller model to another Controller model
In case my HP Proliant DL380 G6 & G7 failed, can I swap all HDD to HP Proliant DL380 G9. HP Proliant DL380 G7 is using the different controller (HP Smart Array Controllers P410i) and HP Proliant ...
-1 votes
1 answer
71 views
MSA70 Upgrade options
Recently I purchased MSA70. Unfortunately I did read specs properly. In my project, I need as much I/O operations as possible. MSA70 is only 3Gbps, so my question is: is it any possibility to upgrade ...
- 3
0 votes
0 answers
152 views
Smart Array P812 External ports don't detect backplane with SAS HDDs
I've found some articles that P812 do not see SATA drives via external ports after updating firmware 5.14 and above. But I can't find any mentions about restrictions with SAS hard drives. (I have two ...
- 13
0 votes
1 answer
4k views
HPE SSA: After completing the configuration - reboot the system
From the HPE ProLiant System Utilities (BIOS) I booted into HPE Smart Storage Administrator (SSA) to migrate a logical drive with RAID6 (and existing data) to RAID5. After starting the migration task, ...
- 787
0 votes
0 answers
202 views
Setting up raid hardware with out deleting data
so I have a home lab, and in the beginning, I started with only 1 DISK, and in the raid config, I bypassed the raid because I didn't have 2 disks to make a RAID 10 or 1, but now, I want some ...
- 139
1 vote
1 answer
1k views
HP ProLiant DL380 G7 (P410i) compatible drives
I have recently been looking to do an upgrade on my server recently by upgrading to using SSDs (2.5 inch). I have done a lot of late night googling and have found that many drives have an issue with ...
- 42
-1 votes
2 answers
1k views
Enable Smart Array P400 HP Proliant DL 120 G7
I have a HP ProLiant D7 120DL with a Smart Array P400. After doing BIOS "Restore Default System Settings" the Smart Array can't see the drives attached to it. When starting the server, Smart ...
- 119
0 votes
1 answer
253 views
Hp Proliant DL120 G7 won't show ORCA
I have on old server, HP Proliant DL120 G7. I configured it with 4 500GB Hard Disk in RAID 10. With this configuration I was able to enter in ORCA setup and the hard drives where connected. Then I ...
- 119
0 votes
1 answer
627 views
HPACUCLI Remotely make active spare permanent member
We have an old HP server - we let the HPE contract expire as it'll be decom'd soon, and our monitoring has flagged a failed disk. For various reasons it's difficult to organise access to the server, ...
- 316
1 vote
2 answers
6k views
DL380p Gen8 E5-2640v2 p420i smart array controller dead
HP DL380p Gen8 E5-2640v2 US Svr/S-Buy Product ID: 653200-B21 Hey there I've got the dreaded but not uncommon: Slot 0 HP Smart Array P420i Controller nitializing… 1783-Slot 0 Drive Array Controller ...
- 11
0 votes
2 answers
863 views
DL380 G10 - P816 controller - Extending LD produces error about max size, even though there is more space in the Array
Array A on this DL380 G10 consists of 9 1.9TB drives in a RAID 5 config. It reports unused space of 619995 MB. There are two logical drives, LD 1 with 13.55 TB (14,000,000 MB), and LD 3 with 97.66 GB (...
- 19
4 votes
5 answers
3k views
Getting a RAID controller to surface scan on a sane schedule
The controller I'm presently working with is quite old, the HP Smart Array P400; in part I want to know how to deal with that controller, but I'm also interested in the general perspective -- if there ...
- 1,668
0 votes
0 answers
2k views
How to get temperature readings of HP P420 RAID PCI-e card?
I have an HP Proliant ML110 G9 Server. Added an HP Smart Array P420 PCI-E card to have real hardware RAID on the server. Everything works fine, but I noted that the P420's processor was extremely hot (...
- 41
0 votes
1 answer
214 views
tested hot swap, now drive is in predictive failure
I have a DL360 G6 (yes I know). I decided to test hot swap and replaced a drive with another one. THe other one failed, so I put the previous working drive back in. It's now in "predictive ...
- 109
2 votes
1 answer
399 views
Troubleshooting frozen disk when queue is full
I have a system (centos 7.8) with k8s installed on top. After a few days of normal operations (system load is ~30% and disk activity is around 60 iops, not saturated), the system goes to an unstable ...
- 175
3 votes
1 answer
4k views
How is the HPE SSA "remove drives" command supposed to work to shrink an array?
I have an HPE ProLiant DL380 Gen9 Server with 15 internal 8TB SAS LFF drives, in a RAID6 configuration through an HP Smart Array P840ar controller. It contains a single 94.6 TB Logical Drive [Size: ...
4 votes
3 answers
886 views
SAS RAID5 Disk failure, replacement enclosure not matching
A SAS disk in RAID5 array failed yesterday and I'm about to replace it, however I noticed the front enclosure wasn't matching the rest of the disks. The array consists of 300GB 10K SAS disks with the ...
- 291
1 vote
1 answer
11k views
HP proliant cache module failure
In our windows server environment, we often get the alert for HP servers that storage cache module has failed. What exactly is the function of cache module?
0 votes
2 answers
4k views
HP DL380e Gen8 NMI error
I have an HP DL380e Gen8 with P420 RAID controller that was powered on 24h per day at my previous job for 7 Months without any issues running a few VMs. After changing job I had the server at home for ...
- 513
0 votes
0 answers
260 views
Server won't boot after adding two new disks
I have an HP ML350 G6 server with 3 600Gb SAS drives on RAID5. I added 2 new 1Tb disks and configured a new Array with RAID1. Al of a sudden I got the blue screen of death, the server rebooted and now ...
- 1
1 vote
3 answers
3k views
Windows Server 2019 Hyper-V guest disk performance
I have a site who run a very IO-sensitive application (Accredo Saturn); it's an accounting/CRM package written in Delphi with a local flat-file database. For various historical reasons the site was ...
- 31
0 votes
1 answer
734 views
Remove logicaldrive in Smart Array P420i
i've a DL380p with Smart Array P420i. On this server we have some logicaldrives: root@server:~# hpacucli ctrl all show config Smart Array P420i in Slot 0 (Embedded) (sn: XXXXXXX) array A (...
-1 votes
2 answers
609 views
HP Proliant DL180 G6 HHD failure and replacement
One of the HP HDD in our HP Proliant DL180 G6 had failed, I've replaced the failed HDD with a standard 1 TB Seagate HDD, the Array controller won't start rebuilding on a Seagate, I had the new Seagate ...
- 101
0 votes
1 answer
1k views
HP Smart Array Controller Not Showing in BIOS
I am currently setting up a HP DL380p Gen8 and I am trying to use a Smart Array P822 controller with it. However, this controller is not showing up in the BIOS so it doesn't detect in windows. The ...
- 21
0 votes
0 answers
4k views
PAGE_FAULT_IN_NONPAGED_AREA (srv.sys) Windows Server 2012 r2
I have an HP proliant 380 gen9 server. The issue started with the server restarting it self on check the ilo logs i found out that we had smart battery failure so we replaced it. After turning it on ...
- 1
0 votes
1 answer
801 views
How to configure HP Smart Array P822 controller with single SAS HDD
I have SAS Seagate Exos HDD and HP P822 Smart Array controller with 2GB cache with battery backup. I don't want to create any arrays, this is supposed to be single storage HDD in my workstation. All ...
- 1
2 votes
0 answers
7k views
How to identify which disk is failing in a HP ProLiant RAID controller?
I have a hard time identifying which drive is failing in my HP ProLiant DL360p Gen8. It has the following RAID controller: Smart Array P420i. I see tons of errors in dmesg: [40425140.998750] sd 0:1:0:...
- 347
0 votes
1 answer
11k views
Debian on HP Gen9 — most recent hpssacli appears to be too old
I've installed a recent Debian 10 Buster system on to the server, which is HPE DL360 Gen9. It has P440ar adapter, which works with the "new" hpsa driver. As far as I remember, RAIDs were configured ...
- 15.8k
1 vote
1 answer
5k views
HPE Raid logical drives not showing in Windows
I'm trying to provision a new server with Windows Server 2019. I have used Intelligent Provisioning to create three arrays: HPE Proliant ML110 - HPE Smart Array E208i-p SR Gen10 2 x SSD Raid 0 - O/S ...
- 121