SAMDUE_TimerInterrupt Library

Imagine you have a system with a mission-critical function, measuring water level and control the sump pump or doing something much more important. You normally use a software timer to poll, or even place the function in loop(). But what if another function is blocking the loop() or setup().

So your function might not be executed, and the result would be disastrous.

You'd prefer to have your function called, no matter what happening with other functions (busy loop, bug, etc.).

The correct choice is to use a Hardware Timer with Interrupt to call your function.

These hardware timers, using interrupt, still work even if other functions are blocking. Moreover, they are much more precise (certainly depending on clock frequency accuracy) than other software timers using millis() or micros(). That's necessary if you need to measure some data requiring better accuracy.

Functions using normal software timers, relying on loop() and calling millis(), won't work if the loop() or setup() is blocked by certain operation. For example, certain function is blocking while it's connecting to WiFi or some services.

The catch is your function is now part of an ISR (Interrupt Service Routine), and must be lean / mean, and follow certain rules. More to read on:

HOWTO Attach Interrupt

Currently supported Boards

Arduino SAM DUE.

Important Notes about ISR

Inside the attached function, delay() won’t work and the value returned by millis() will not increment. Serial data received while in the function may be lost. You should declare as volatile any variables that you modify within the attached function.
Typically global variables are used to pass data between an ISR and the main program. To make sure variables shared between an ISR and the main program are updated correctly, declare them as volatile.

Prerequisites

Arduino IDE 1.8.19+ for Arduino.
Arduino SAM DUE core v1.6.12+ for SAM DUE ARM Cortex-M3 boards
Blynk library 1.1.0+. to use with certain example.
To use with certain example, depending on which Ethernet card you're using:

Ethernet_Generic library v2.7.1+ for W5100, W5200 and W5500.
EthernetENC library v2.0.3+ for ENC28J60. . New and Better
UIPEthernet library v2.0.12+ for ENC28J60.

To use with certain example

SimpleTimer library for ISR_16_Timers_Array and ISR_16_Timers_Array_Complex examples.

Installation

Use Arduino Library Manager

The best and easiest way is to use Arduino Library Manager. Search for SAMDUE_TimerInterrupt, then select / install the latest version. You can also use this link for more detailed instructions.

Manual Install

Another way to install is to:

Navigate to SAMDUE_TimerInterrupt page.
Download the latest release SAMDUE_TimerInterrupt-main.zip.
Extract the zip file to SAMDUE_TimerInterrupt-main directory
Copy whole SAMDUE_TimerInterrupt-main folder to Arduino libraries' directory such as ~/Arduino/libraries/.

VS Code & PlatformIO

Install VS Code
Install PlatformIO
Install SAMDUE_TimerInterrupt library by using Library Manager. Search for SAMDUE_TimerInterrupt in Platform.io Author's Libraries
Use included platformio.ini file from examples to ensure that all dependent libraries will installed automatically. Please visit documentation for the other options and examples at Project Configuration File

Packages' Patches

1. For Arduino SAM DUE boards

To be able to compile and run on SAM DUE boards, you have to copy the whole SAM DUE directory into Arduino sam directory (~/.arduino15/packages/arduino/hardware/sam/1.6.12).

Supposing the Arduino SAM core version is 1.6.12. This file must be copied into the directory:

~/.arduino15/packages/arduino/hardware/sam/1.6.12/platform.txt

Whenever a new version is installed, remember to copy this file into the new version directory. For example, new version is x.yy.zz This file must be copied into the directory:

~/.arduino15/packages/arduino/hardware/sam/x.yy.zz/platform.txt

Libraries' Patches

Notes: These patches are totally optional and necessary only when you use the related Ethernet library and get certain error or issues.

1. For application requiring 2K+ HTML page

If your application requires 2K+ HTML page, the current Ethernet library must be modified if you are using W5200/W5500 Ethernet shields. W5100 is not supported for 2K+ buffer. If you use boards requiring different CS/SS pin for W5x00 Ethernet shield, for example ESP32, ESP8266, nRF52, etc., you also have to modify the following libraries to be able to specify the CS/SS pin correctly.

2. For Ethernet library

To fix Ethernet library, just copy these following files into the Ethernet library directory to overwrite the old files:

3. For EthernetLarge library

To fix EthernetLarge library, just copy these following files into the EthernetLarge library directory to overwrite the old files:

4. For Ethernet2 library

To fix Ethernet2 library, just copy these following files into the Ethernet2 library directory to overwrite the old files:

To add UDP Multicast support, necessary for the UPnP_Generic library:

5. For Ethernet3 library

To fix Ethernet3 library, just copy these following files into the Ethernet3 library directory to overwrite the old files:

6. For UIPEthernet library

To be able to compile and run on nRF52 boards with ENC28J60 using UIPEthernet library, you have to copy these following files into the UIPEthernet utility directory to overwrite the old files:

7. For fixing ESP32 compile error

To fix ESP32 compile error, just copy the following file into the ESP32 cores/esp32 directory (e.g. ./arduino-1.8.12/hardware/espressif/cores/esp32) to overwrite the old file:

Server.h

HOWTO Fix `Multiple Definitions` Linker Error

The current library implementation, using xyz-Impl.h instead of standard xyz.cpp, possibly creates certain Multiple Definitions Linker error in certain use cases.

You can include these .hpp files

// Can be included as many times as necessary, without `Multiple Definitions` Linker Error #include "SAMDUETimerInterrupt.hpp" //https://github.com/khoih-prog/SAMDUE_TimerInterrupt // Can be included as many times as necessary, without `Multiple Definitions` Linker Error #include "SAMDUE_ISR_Timer.hpp" //https://github.com/khoih-prog/SAMDUE_TimerInterrupt

in many files. But be sure to use the following .h files in just 1 .h, .cpp or .ino file, which must not be included in any other file, to avoid Multiple Definitions Linker Error

// To be included only in main(), .ino with setup() to avoid `Multiple Definitions` Linker Error #include "SAMDUETimerInterrupt.h" //https://github.com/khoih-prog/SAMDUE_TimerInterrupt // To be included only in main(), .ino with setup() to avoid `Multiple Definitions` Linker Error #include "SAMDUE_ISR_Timer.h" //https://github.com/khoih-prog/SAMDUE_TimerInterrupt

Check the new multiFileProject example for a HOWTO demo.

New from v1.0.1

Now with these new 16 ISR-based timers (while consuming only 1 hardware timer), the maximum interval is practically unlimited (limited only by unsigned long milliseconds). The accuracy is nearly perfect compared to software timers. The most important feature is they're ISR-based timers Therefore, their executions are not blocked by bad-behaving functions / tasks. This important feature is absolutely necessary for mission-critical tasks.

The ISR_16_Timers_Array and ISR_Timer_Complex_Ethernet examples will demonstrate the nearly perfect accuracy compared to software timers by printing the actual elapsed millisecs of each type of timers. Being ISR-based timers, their executions are not blocked by bad-behaving functions / tasks, such as connecting to WiFi, Internet and Blynk services. You can also have many (up to 16) timers to use. This non-being-blocked important feature is absolutely necessary for mission-critical tasks. You'll see blynkTimer Software is blocked while system is connecting to WiFi / Internet / Blynk, as well as by blocking task in loop(), using delay() function as an example. The elapsed time then is very unaccurate

Usage

Before using any Timer, you have to make sure the Timer has not been used by any other purpose.

1. Using only Hardware Timer directly

1.1 Init Hardware Timer

// Interval in microsecs attachDueInterrupt(TIMER1_INTERVAL_MS * 1000, TimerHandler1, "ITimer1");

1.2 Set Hardware Timer Interval and attach Timer Interrupt Handler function

void TimerHandler(void) { // Doing something here inside ISR } #define TIMER_INTERVAL_MS 1000 // 1s = 1000ms uint16_t attachDueInterrupt(double microseconds, timerCallback callback, const char* TimerName) { DueTimerInterrupt dueTimerInterrupt = DueTimer.getAvailable(); dueTimerInterrupt.attachInterruptInterval(microseconds, callback); uint16_t timerNumber = dueTimerInterrupt.getTimerNumber(); Serial.print(TimerName); Serial.print(" attached to Timer("); Serial.print(timerNumber); Serial.println(")"); return timerNumber; } void setup() { .... // Interval in microsecs attachDueInterrupt(TIMER_INTERVAL_MS * 1000, TimerHandler, "ITimer"); }

2. Using 16 ISR_based Timers from 1 Hardware Timer

2.1 Init Hardware Timer and ISR-based Timer

// Interval in microsecs attachDueInterrupt(TIMER1_INTERVAL_MS * 1000, TimerHandler1, "ITimer1");

2.2 Set Hardware Timer Interval and attach Timer Interrupt Handler functions

void TimerHandler(void) { ISR_Timer.run(); } #define HW_TIMER_INTERVAL_MS 1L #define TIMER_INTERVAL_2S 2000L #define TIMER_INTERVAL_5S 5000L #define TIMER_INTERVAL_11S 11000L #define TIMER_INTERVAL_101S 101000L // In SAM DUE, avoid doing something fancy in ISR, for example complex Serial.print with String() argument // The pure simple Serial.prints here are just for demonstration and testing. Must be eliminate in working environment // Or you can get this run-time error / crash void doingSomething2s() { // Doing something here inside ISR } void doingSomething5s() { // Doing something here inside ISR } void doingSomething11s() { // Doing something here inside ISR } void doingSomething101s() { // Doing something here inside ISR } uint16_t attachDueInterrupt(double microseconds, timerCallback callback, const char* TimerName) { DueTimerInterrupt dueTimerInterrupt = DueTimer.getAvailable(); dueTimerInterrupt.attachInterruptInterval(microseconds, callback); uint16_t timerNumber = dueTimerInterrupt.getTimerNumber(); Serial.print(TimerName); Serial.print(" attached to Timer("); Serial.print(timerNumber); Serial.println(")"); return timerNumber; } void setup() { .... // Interval in microsecs attachDueInterrupt(HW_TIMER_INTERVAL_MS * 1000, TimerHandler, "ITimer"); // Just to demonstrate, don't use too many ISR Timers if not absolutely necessary // You can use up to 16 timer for each ISR_Timer ISR_Timer.setInterval(TIMER_INTERVAL_2S, doingSomething2s); ISR_Timer.setInterval(TIMER_INTERVAL_5S, doingSomething5s); ISR_Timer.setInterval(TIMER_INTERVAL_11S, doingSomething11s); ISR_Timer.setInterval(TIMER_INTERVAL_101S, doingSomething101s); }

Examples:

Example ISR_16_Timers_Array_Complex

SAMDUE_TimerInterrupt/examples/ISR_16_Timers_Array_Complex/ISR_16_Timers_Array_Complex.ino

Lines 35 to 367 in 34fbcaf

     #if !( defined(ARDUINO_SAM_DUE) || defined(__SAM3X8E__) )  
   #error This code is designed to run on SAM DUE board / platform! Please check your Tools->Board setting.  
   #endif  
    
   // These define's must be placed at the beginning before #include "SAMDUETimerInterrupt.h"  
   // _TIMERINTERRUPT_LOGLEVEL_ from 0 to 4  
   // Don't define _TIMERINTERRUPT_LOGLEVEL_ > 0. Only for special ISR debugging only. Can hang the system.  
   // Don't define TIMER_INTERRUPT_DEBUG > 2. Only for special ISR debugging only. Can hang the system.  
   #define TIMER_INTERRUPT_DEBUG 0  
   #define _TIMERINTERRUPT_LOGLEVEL_ 3  
    
   // To be included only in main(), .ino with setup() to avoid `Multiple Definitions` Linker Error  
   #include "SAMDUETimerInterrupt.h"  
    
   // To be included only in main(), .ino with setup() to avoid `Multiple Definitions` Linker Error  
   #include "SAMDUE_ISR_Timer.h"  
    
   #include <SimpleTimer.h> // https://github.com/jfturcot/SimpleTimer  
    
   #ifndef LED_BUILTIN  
   #define LED_BUILTIN 13  
   #endif  
    
   #ifndef LED_BLUE  
   #define LED_BLUE 2  
   #endif  
    
   #ifndef LED_RED  
   #define LED_RED 3  
   #endif  
    
   #define HW_TIMER_INTERVAL_US 10000L  
    
   volatile uint32_t startMillis = 0;  
    
   // Init SAMDUE_ISR_Timer  
   // Each SAMDUE_ISR_Timer can service 16 different ISR-based timers  
   SAMDUE_ISR_Timer ISR_Timer;  
    
   #define LED_TOGGLE_INTERVAL_MS 2000L  
    
   void TimerHandler()  
   {  
   static bool toggle = false;  
   static int timeRun = 0;  
    
   ISR_Timer.run();  
    
   // Toggle LED every LED_TOGGLE_INTERVAL_MS = 2000ms = 2s  
   if (++timeRun == ((LED_TOGGLE_INTERVAL_MS * 1000) / HW_TIMER_INTERVAL_US) )  
   {  
   timeRun = 0;  
    
   //timer interrupt toggles pin LED_BUILTIN  
   digitalWrite(LED_BUILTIN, toggle);  
   toggle = !toggle;  
   }  
   }  
    
   /////////////////////////////////////////////////  
    
   #define NUMBER_ISR_TIMERS 16  
    
   typedef void (*irqCallback) ();  
    
   /////////////////////////////////////////////////  
    
   #define USE_COMPLEX_STRUCT true  
    
   #if USE_COMPLEX_STRUCT  
    
   typedef struct  
   {  
   irqCallback irqCallbackFunc;  
   uint32_t TimerInterval;  
   unsigned long deltaMillis;  
   unsigned long previousMillis;  
   } ISRTimerData;  
    
   // In NRF52, avoid doing something fancy in ISR, for example Serial.print()  
   // The pure simple Serial.prints here are just for demonstration and testing. Must be eliminate in working environment  
   // Or you can get this run-time error / crash  
    
   void doingSomething(int index);  
    
   #else  
    
   volatile unsigned long deltaMillis [NUMBER_ISR_TIMERS] = { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 };  
   volatile unsigned long previousMillis [NUMBER_ISR_TIMERS] = { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 };  
    
   // You can assign any interval for any timer here, in milliseconds  
   uint32_t TimerInterval[NUMBER_ISR_TIMERS] =  
   {  
   5000L, 10000L, 15000L, 20000L, 25000L, 30000L, 35000L, 40000L,  
   45000L, 50000L, 55000L, 60000L, 65000L, 70000L, 75000L, 80000L  
   };  
    
   void doingSomething(int index)  
   {  
   unsigned long currentMillis = millis();  
    
   deltaMillis[index] = currentMillis - previousMillis[index];  
   previousMillis[index] = currentMillis;  
   }  
    
   #endif  
    
   ////////////////////////////////////  
   // Shared  
   ////////////////////////////////////  
    
   void doingSomething0()  
   {  
   doingSomething(0);  
   }  
    
   void doingSomething1()  
   {  
   doingSomething(1);  
   }  
    
   void doingSomething2()  
   {  
   doingSomething(2);  
   }  
    
   void doingSomething3()  
   {  
   doingSomething(3);  
   }  
    
   void doingSomething4()  
   {  
   doingSomething(4);  
   }  
    
   void doingSomething5()  
   {  
   doingSomething(5);  
   }  
    
   void doingSomething6()  
   {  
   doingSomething(6);  
   }  
    
   void doingSomething7()  
   {  
   doingSomething(7);  
   }  
    
   void doingSomething8()  
   {  
   doingSomething(8);  
   }  
    
   void doingSomething9()  
   {  
   doingSomething(9);  
   }  
    
   void doingSomething10()  
   {  
   doingSomething(10);  
   }  
    
   void doingSomething11()  
   {  
   doingSomething(11);  
   }  
    
   void doingSomething12()  
   {  
   doingSomething(12);  
   }  
    
   void doingSomething13()  
   {  
   doingSomething(13);  
   }  
    
   void doingSomething14()  
   {  
   doingSomething(14);  
   }  
    
   void doingSomething15()  
   {  
   doingSomething(15);  
   }  
    
   #if USE_COMPLEX_STRUCT  
    
   ISRTimerData curISRTimerData[NUMBER_ISR_TIMERS] =  
   {  
   //irqCallbackFunc, TimerInterval, deltaMillis, previousMillis  
   { doingSomething0, 5000L, 0, 0 },  
   { doingSomething1, 10000L, 0, 0 },  
   { doingSomething2, 15000L, 0, 0 },  
   { doingSomething3, 20000L, 0, 0 },  
   { doingSomething4, 25000L, 0, 0 },  
   { doingSomething5, 30000L, 0, 0 },  
   { doingSomething6, 35000L, 0, 0 },  
   { doingSomething7, 40000L, 0, 0 },  
   { doingSomething8, 45000L, 0, 0 },  
   { doingSomething9, 50000L, 0, 0 },  
   { doingSomething10, 55000L, 0, 0 },  
   { doingSomething11, 60000L, 0, 0 },  
   { doingSomething12, 65000L, 0, 0 },  
   { doingSomething13, 70000L, 0, 0 },  
   { doingSomething14, 75000L, 0, 0 },  
   { doingSomething15, 80000L, 0, 0 }  
   };  
    
   void doingSomething(int index)  
   {  
   unsigned long currentMillis = millis();  
    
   curISRTimerData[index].deltaMillis = currentMillis - curISRTimerData[index].previousMillis;  
   curISRTimerData[index].previousMillis = currentMillis;  
   }  
    
   #else  
    
   irqCallback irqCallbackFunc[NUMBER_ISR_TIMERS] =  
   {  
   doingSomething0, doingSomething1, doingSomething2, doingSomething3,  
   doingSomething4, doingSomething5, doingSomething6, doingSomething7,  
   doingSomething8, doingSomething9, doingSomething10, doingSomething11,  
   doingSomething12, doingSomething13, doingSomething14, doingSomething15  
   };  
    
   #endif  
   ///////////////////////////////////////////  
    
   #define SIMPLE_TIMER_MS 2000L  
    
   // Init SimpleTimer  
   SimpleTimer simpleTimer;  
    
   // Here is software Timer, you can do somewhat fancy stuffs without many issues.  
   // But always avoid  
   // 1. Long delay() it just doing nothing and pain-without-gain wasting CPU power.Plan and design your code / strategy ahead  
   // 2. Very long "do", "while", "for" loops without predetermined exit time.  
   void simpleTimerDoingSomething2s()  
   {  
   static unsigned long previousMillis = startMillis;  
    
   unsigned long currMillis = millis();  
    
   Serial.print(F("SimpleTimer : "));Serial.print(SIMPLE_TIMER_MS / 1000);  
   Serial.print(F(", ms : ")); Serial.print(currMillis);  
   Serial.print(F(", Dms : ")); Serial.println(currMillis - previousMillis);  
    
   for (uint16_t i = 0; i < NUMBER_ISR_TIMERS; i++)  
   {  
   #if USE_COMPLEX_STRUCT  
   Serial.print(F("Timer : ")); Serial.print(i);  
   Serial.print(F(", programmed : ")); Serial.print(curISRTimerData[i].TimerInterval);  
   Serial.print(F(", actual : ")); Serial.println(curISRTimerData[i].deltaMillis);  
   #else  
   Serial.print(F("Timer : ")); Serial.print(i);  
   Serial.print(F(", programmed : ")); Serial.print(TimerInterval[i]);  
   Serial.print(F(", actual : ")); Serial.println(deltaMillis[i]);  
   #endif  
   }  
    
   previousMillis = currMillis;  
   }  
    
   uint16_t attachDueInterrupt(double microseconds, timerCallback callback, const char* TimerName)  
   {  
   DueTimerInterrupt dueTimerInterrupt = DueTimer.getAvailable();  
    
   dueTimerInterrupt.attachInterruptInterval(microseconds, callback);  
    
   uint16_t timerNumber = dueTimerInterrupt.getTimerNumber();  
    
   Serial.print(TimerName); Serial.print(F(" attached to Timer(")); Serial.print(timerNumber); Serial.println(F(")"));  
    
   return timerNumber;  
   }  
    
   void setup()  
   {  
   pinMode(LED_BUILTIN, OUTPUT);  
    
   Serial.begin(115200);  
   while (!Serial);  
    
   delay(100);  
    
   Serial.print(F("\nStarting ISR_16_Timers_Array_Complex on ")); Serial.println(BOARD_NAME);  
   Serial.println(SAMDUE_TIMER_INTERRUPT_VERSION);  
   Serial.print(F("CPU Frequency = ")); Serial.print(F_CPU / 1000000); Serial.println(F(" MHz"));  
   Serial.print(F("Timer Frequency = ")); Serial.print(SystemCoreClock / 1000000); Serial.println(F(" MHz"));  
    
   // Interval in microsecs  
   attachDueInterrupt(HW_TIMER_INTERVAL_US, TimerHandler, "ITimer");  
    
   startMillis = millis();  
    
   // Just to demonstrate, don't use too many ISR Timers if not absolutely necessary  
   // You can use up to 16 timer for each ISR_Timer  
   for (uint8_t i = 0; i < NUMBER_ISR_TIMERS; i++)  
   {  
   #if USE_COMPLEX_STRUCT  
   curISRTimerData[i].previousMillis = startMillis;  
   ISR_Timer.setInterval(curISRTimerData[i].TimerInterval, curISRTimerData[i].irqCallbackFunc);  
   #else  
   previousMillis[i] = startMillis;  
   ISR_Timer.setInterval(TimerInterval[i], irqCallbackFunc[i]);  
   #endif  
   }  
    
   // You need this timer for non-critical tasks. Avoid abusing ISR if not absolutely necessary.  
   simpleTimer.setInterval(SIMPLE_TIMER_MS, simpleTimerDoingSomething2s);  
   }  
    
   #define BLOCKING_TIME_MS 10000L  
    
   void loop()  
   {  
   // This unadvised blocking task is used to demonstrate the blocking effects onto the execution and accuracy to Software timer  
   // You see the time elapse of ISR_Timer still accurate, whereas very unaccurate for Software Timer  
   // The time elapse for 2000ms software timer now becomes 3000ms (BLOCKING_TIME_MS)  
   // While that of ISR_Timer is still prefect.  
   delay(BLOCKING_TIME_MS);  
    
   // You need this Software timer for non-critical tasks. Avoid abusing ISR if not absolutely necessary  
   // You don't need to and never call ISR_Timer.run() here in the loop(). It's already handled by ISR timer.  
   simpleTimer.run();  
   }  
 

Debug Terminal Output Samples

1. ISR_Timer_Complex_Ethernet on Arduino SAM DUE

The following is the sample terminal output when running example ISR_Timer_Complex_Ethernet on Arduino SAM DUE to demonstrate the accuracy of ISR Hardware Timer, especially when system is very busy. The ISR timer is programmed for 2s, is activated exactly after 2.000s !!!

While software timer, programmed for 2s, is activated after 10.917s !!!. Then in loop(), it's also activated every 3s.

Starting ISR_Timer_Complex_Ethernet on SAM DUE SAMDUE_TimerInterrupt v1.3.0 CPU Frequency = 84 MHz Using Timer(0) = TC0, channel = 0, IRQ = TC0_IRQn Timer(0), us = 50000.00 ITimer attached to Timer(0) [5] Getting IP... [7] MAC: FE-8A-F1-EA-DE-82 _pinCS = 0 W5100 init, using SS_PIN_DEFAULT = 10, new ss_pin = 10, W5100Class::ss_pin = 10 W5100::init: W5100, SSIZE =4096 2s: Delta ms = 2000 2s: Delta ms = 2000 [7728] IP:192.168.2.134 [7728] ___ __ __ / _ )/ /_ _____ / /__ / _ / / // / _ \/ '_/ /____/_/\_, /_//_/_/\_\ /___/ v0.6.1 on Arduino Due [7732] BlynkArduinoClient.connect: Connecting to account.duckdns.org:8080 [7849] Ready (ping: 6ms). IP = 192.168.2.134 2s: Delta ms = 2000 2s: Delta ms = 2000 5s: Delta ms = 5000 blynkDoingSomething2s: Delta programmed ms = 2000, actual = 10917 2s: Delta ms = 2000 blynkDoingSomething2s: Delta programmed ms = 2000, actual = 3000 2s: Delta ms = 2000 5s: Delta ms = 5000 2s: Delta ms = 2000 blynkDoingSomething2s: Delta programmed ms = 2000, actual = 3000 2s: Delta ms = 2000 blynkDoingSomething2s: Delta programmed ms = 2000, actual = 3000 2s: Delta ms = 2000 5s: Delta ms = 5000 2s: Delta ms = 2000 11s: Delta ms = 11000 blynkDoingSomething2s: Delta programmed ms = 2000, actual = 3000 2s: Delta ms = 2000 5s: Delta ms = 5000 blynkDoingSomething2s: Delta programmed ms = 2000, actual = 3000 2s: Delta ms = 2000 2s: Delta ms = 2000 blynkDoingSomething2s: Delta programmed ms = 2000, actual = 3000 2s: Delta ms = 2000 5s: Delta ms = 5000 blynkDoingSomething2s: Delta programmed ms = 2000, actual = 3000 2s: Delta ms = 2000 11s: Delta ms = 11000 2s: Delta ms = 2000 blynkDoingSomething2s: Delta programmed ms = 2000, actual = 3000 5s: Delta ms = 5000 2s: Delta ms = 2000 blynkDoingSomething2s: Delta programmed ms = 2000, actual = 3000 2s: Delta ms = 2000 2s: Delta ms = 2000 5s: Delta ms = 5000 blynkDoingSomething2s: Delta programmed ms = 2000, actual = 3000 2s: Delta ms = 2000 blynkDoingSomething2s: Delta programmed ms = 2000, actual = 3000 2s: Delta ms = 2000 11s: Delta ms = 11000 5s: Delta ms = 5000 2s: Delta ms = 2000 blynkDoingSomething2s: Delta programmed ms = 2000, actual = 3000 2s: Delta ms = 2000 blynkDoingSomething2s: Delta programmed ms = 2000, actual = 3000 2s: Delta ms = 2000 5s: Delta ms = 5000 2s: Delta ms = 2000 blynkDoingSomething2s: Delta programmed ms = 2000, actual = 3000 2s: Delta ms = 2000 5s: Delta ms = 5000 11s: Delta ms = 11000 blynkDoingSomething2s: Delta programmed ms = 2000, actual = 3000 2s: Delta ms = 2000 2s: Delta ms = 2000 blynkDoingSomething2s: Delta programmed ms = 2000, actual = 3000

2. TimerInterruptTest on Arduino SAM DUE

The following is the sample terminal output when running example TimerInterruptTest on Arduino SAM DUE to demonstrate how to start/stop Hardware Timers.

Starting TimerInterruptTest on SAM DUE SAMDUE_TimerInterrupt v1.3.0 CPU Frequency = 84 MHz Timer Frequency = 84 MHz Using Timer(0) = TC0, channel = 0, IRQ = TC0_IRQn ITimer0 attached to Timer(0) Using Timer(1) = TC0, channel = 1, IRQ = TC1_IRQn ITimer1 attached to Timer(1) ITimer0: millis() = 1104, delta = 1104 ITimer0: millis() = 2104, delta = 1000 ITimer0: millis() = 3104, delta = 1000 ITimer1: millis() = 3111, delta = 3111 ITimer0: millis() = 4104, delta = 1000 Stop ITimer0, millis() = 5001 ITimer1: millis() = 6111, delta = 3000 ITimer1: millis() = 9111, delta = 3000 Start ITimer0, millis() = 10002 ITimer0: millis() = 11002, delta = 1000 ITimer0: millis() = 12002, delta = 1000 ITimer1: millis() = 12111, delta = 3000 ITimer0: millis() = 13002, delta = 1000 ITimer0: millis() = 14002, delta = 1000 Stop ITimer1, millis() = 15001 ITimer0: millis() = 15002, delta = 1000 Stop ITimer0, millis() = 15003 Start ITimer0, millis() = 20004 ITimer0: millis() = 21004, delta = 1000 ITimer0: millis() = 22004, delta = 1000 ITimer0: millis() = 23004, delta = 1000 ITimer0: millis() = 24004, delta = 1000 ITimer0: millis() = 25004, delta = 1000 Stop ITimer0, millis() = 25005 Start ITimer1, millis() = 30002 Start ITimer0, millis() = 30006 ITimer0: millis() = 31006, delta = 1000 ITimer0: millis() = 32006, delta = 1000 ITimer1: millis() = 33002, delta = 3000 ITimer0: millis() = 33006, delta = 1000 ITimer0: millis() = 34006, delta = 1000 ITimer0: millis() = 35006, delta = 1000 Stop ITimer0, millis() = 35007 ITimer1: millis() = 36002, delta = 3000 ITimer1: millis() = 39002, delta = 3000 Start ITimer0, millis() = 40008 ITimer0: millis() = 41008, delta = 1000 ITimer1: millis() = 42002, delta = 3000 ITimer0: millis() = 42008, delta = 1000 ITimer0: millis() = 43008, delta = 1000 ITimer0: millis() = 44008, delta = 1000 ITimer1: millis() = 45002, delta = 3000 Stop ITimer1, millis() = 45003 ITimer0: millis() = 45008, delta = 1000 Stop ITimer0, millis() = 45009

3. ISR_16_Timers_Array on Arduino SAM DUE

The following is the sample terminal output when running example ISR_16_Timers_Array on Arduino SAM DUE to demonstrate the accuracy and how to use 16 ISR Timers from just 1 Hardware Timer.

Starting ISR_16_Timers_Array on SAM DUE SAMDUE_TimerInterrupt v1.3.0 CPU Frequency = 84 MHz Timer Frequency = 84 MHz Using Timer(0) = TC0, channel = 0, IRQ = TC0_IRQn Timer(0), us = 100.00 ITimer attached to Timer(0) 1s: Delta ms = 1006, ms = 1006 1s: Delta ms = 1000, ms = 2006 1s: Delta ms = 1000, ms = 3006 1s: Delta ms = 1000, ms = 4006 1s: Delta ms = 1000, ms = 5006 1s: Delta ms = 1000, ms = 6006 1s: Delta ms = 1000, ms = 7006 1s: Delta ms = 1000, ms = 8006 1s: Delta ms = 1000, ms = 9006 1s: Delta ms = 1000, ms = 10006 1s: Delta ms = 1000, ms = 11006 simpleTimer2s: Dms=2000, actual=11118 1s: Delta ms = 1000, ms = 12006 1s: Delta ms = 1000, ms = 13006 1s: Delta ms = 1000, ms = 14006 1s: Delta ms = 1000, ms = 15006 1s: Delta ms = 1000, ms = 16006 1s: Delta ms = 1000, ms = 17006 1s: Delta ms = 1000, ms = 18006 1s: Delta ms = 1000, ms = 19006 1s: Delta ms = 1000, ms = 20006 1s: Delta ms = 1000, ms = 21006 1s: Delta ms = 1000, ms = 22006 simpleTimer2s: Dms=2000, actual=11111 1s: Delta ms = 1000, ms = 23006 1s: Delta ms = 1000, ms = 24006 1s: Delta ms = 1000, ms = 25006 1s: Delta ms = 1000, ms = 26006 1s: Delta ms = 1000, ms = 27006 1s: Delta ms = 1000, ms = 28006 1s: Delta ms = 1000, ms = 29006 1s: Delta ms = 1000, ms = 30006 1s: Delta ms = 1000, ms = 31006 1s: Delta ms = 1000, ms = 32006 1s: Delta ms = 1000, ms = 33006 simpleTimer2s: Dms=2000, actual=11111 1s: Delta ms = 1000, ms = 34006 1s: Delta ms = 1000, ms = 35006 1s: Delta ms = 1000, ms = 36006 1s: Delta ms = 1000, ms = 37006 1s: Delta ms = 1000, ms = 38006 1s: Delta ms = 1000, ms = 39006 1s: Delta ms = 1000, ms = 40006 1s: Delta ms = 1000, ms = 41006 1s: Delta ms = 1000, ms = 42006 1s: Delta ms = 1000, ms = 43006 1s: Delta ms = 1000, ms = 44006 simpleTimer2s: Dms=2000, actual=11111 1s: Delta ms = 1000, ms = 45006 1s: Delta ms = 1000, ms = 46006 1s: Delta ms = 1000, ms = 47006

4. Change_Interval on Arduino SAM DUE

The following is the sample terminal output when running example Change_Interval to demonstrate how to change Timer Interval on-the-fly

Starting Change_Interval on SAM DUE SAMDUE_TimerInterrupt v1.3.0 CPU Frequency = 84 MHz Timer Frequency = 84 MHz Using Timer(0) = TC0, channel = 0, IRQ = TC0_IRQn ITimer0 attached to Timer(0) Using Timer(1) = TC0, channel = 1, IRQ = TC1_IRQn ITimer1 attached to Timer(1) Time = 10001, Timer0Count = 19, Timer1Count = 9 Time = 20002, Timer0Count = 39, Timer1Count = 19 ITimer0 attached to Timer(0) ITimer1 attached to Timer(1) Changing Interval, Timer0 = 1000, Timer1 = 2000 Time = 30003, Timer0Count = 49, Timer1Count = 24 Time = 40004, Timer0Count = 59, Timer1Count = 29 ITimer0 attached to Timer(0) ITimer1 attached to Timer(1) Changing Interval, Timer0 = 500, Timer1 = 1000 Time = 50005, Timer0Count = 79, Timer1Count = 39 Time = 60006, Timer0Count = 99, Timer1Count = 49 ITimer0 attached to Timer(0) ITimer1 attached to Timer(1) Changing Interval, Timer0 = 1000, Timer1 = 2000 Time = 70007, Timer0Count = 109, Timer1Count = 54 Time = 80008, Timer0Count = 119, Timer1Count = 59 ITimer0 attached to Timer(0) ITimer1 attached to Timer(1) Changing Interval, Timer0 = 500, Timer1 = 1000 Time = 90009, Timer0Count = 139, Timer1Count = 69

5. ISR_16_Timers_Array_Complex on Arduino SAM DUE

The following is the sample terminal output when running new example ISR_16_Timers_Array_Complex on Arduino SAM DUE to demonstrate the accuracy of ISR Hardware Timer, especially when system is very busy or blocked. The 16 independent ISR timers are programmed to be activated repetitively after certain intervals, is activated exactly after that programmed interval !!!

While software timer, programmed for 2s, is activated after 10.000s in loop()!!!.

In this example, 16 independent ISR Timers are used, yet utilized just one Hardware Timer. The Timer Intervals and Function Pointers are stored in arrays to facilitate the code modification.

Starting ISR_16_Timers_Array_Complex on SAM DUE SAMDUE_TimerInterrupt v1.3.0 CPU Frequency = 84 MHz Timer Frequency = 84 MHz Using Timer(0) = TC0, channel = 0, IRQ = TC0_IRQn ITimer attached to Timer(0) SimpleTimer : 2, ms = 10009, Dms : 10000 Timer : 0, programmed : 5000, actual : 5007 Timer : 1, programmed : 10000, actual : 0 Timer : 2, programmed : 15000, actual : 0 Timer : 3, programmed : 20000, actual : 0 Timer : 4, programmed : 25000, actual : 0 Timer : 5, programmed : 30000, actual : 0 Timer : 6, programmed : 35000, actual : 0 Timer : 7, programmed : 40000, actual : 0 Timer : 8, programmed : 45000, actual : 0 Timer : 9, programmed : 50000, actual : 0 Timer : 10, programmed : 55000, actual : 0 Timer : 11, programmed : 60000, actual : 0 Timer : 12, programmed : 65000, actual : 0 Timer : 13, programmed : 70000, actual : 0 Timer : 14, programmed : 75000, actual : 0 Timer : 15, programmed : 80000, actual : 0 SimpleTimer : 2, ms = 20061, Dms : 10052 Timer : 0, programmed : 5000, actual : 5000 Timer : 1, programmed : 10000, actual : 10000 Timer : 2, programmed : 15000, actual : 15007 Timer : 3, programmed : 20000, actual : 20007 Timer : 4, programmed : 25000, actual : 0 Timer : 5, programmed : 30000, actual : 0 Timer : 6, programmed : 35000, actual : 0 Timer : 7, programmed : 40000, actual : 0 Timer : 8, programmed : 45000, actual : 0 Timer : 9, programmed : 50000, actual : 0 Timer : 10, programmed : 55000, actual : 0 Timer : 11, programmed : 60000, actual : 0 Timer : 12, programmed : 65000, actual : 0 Timer : 13, programmed : 70000, actual : 0 Timer : 14, programmed : 75000, actual : 0 Timer : 15, programmed : 80000, actual : 0 ... SimpleTimer : 2, ms = 140731, Dms : 10057 Timer : 0, programmed : 5000, actual : 5000 Timer : 1, programmed : 10000, actual : 10000 Timer : 2, programmed : 15000, actual : 15000 Timer : 3, programmed : 20000, actual : 20000 Timer : 4, programmed : 25000, actual : 25000 Timer : 5, programmed : 30000, actual : 30000 Timer : 6, programmed : 35000, actual : 35000 Timer : 7, programmed : 40000, actual : 40000 Timer : 8, programmed : 45000, actual : 45000 Timer : 9, programmed : 50000, actual : 50000 Timer : 10, programmed : 55000, actual : 55000 Timer : 11, programmed : 60000, actual : 60000 Timer : 12, programmed : 65000, actual : 65000 Timer : 13, programmed : 70000, actual : 70000 Timer : 14, programmed : 75000, actual : 75007 Timer : 15, programmed : 80000, actual : 80007 SimpleTimer : 2, ms = 150788, Dms : 10057 Timer : 0, programmed : 5000, actual : 5000 Timer : 1, programmed : 10000, actual : 10000 Timer : 2, programmed : 15000, actual : 15000 Timer : 3, programmed : 20000, actual : 20000 Timer : 4, programmed : 25000, actual : 25000 Timer : 5, programmed : 30000, actual : 30000 Timer : 6, programmed : 35000, actual : 35000 Timer : 7, programmed : 40000, actual : 40000 Timer : 8, programmed : 45000, actual : 45000 Timer : 9, programmed : 50000, actual : 50000 Timer : 10, programmed : 55000, actual : 55000 Timer : 11, programmed : 60000, actual : 60000 Timer : 12, programmed : 65000, actual : 65000 Timer : 13, programmed : 70000, actual : 70000 Timer : 14, programmed : 75000, actual : 75000 Timer : 15, programmed : 80000, actual : 80007 SimpleTimer : 2, ms = 160845, Dms : 10057 Timer : 0, programmed : 5000, actual : 5000 Timer : 1, programmed : 10000, actual : 10000 Timer : 2, programmed : 15000, actual : 15000 Timer : 3, programmed : 20000, actual : 20000 Timer : 4, programmed : 25000, actual : 25000 Timer : 5, programmed : 30000, actual : 30000 Timer : 6, programmed : 35000, actual : 35000 Timer : 7, programmed : 40000, actual : 40000 Timer : 8, programmed : 45000, actual : 45000 Timer : 9, programmed : 50000, actual : 50000 Timer : 10, programmed : 55000, actual : 55000 Timer : 11, programmed : 60000, actual : 60000 Timer : 12, programmed : 65000, actual : 65000 Timer : 13, programmed : 70000, actual : 70000 Timer : 14, programmed : 75000, actual : 75000 Timer : 15, programmed : 80000, actual : 80000 SimpleTimer : 2, ms = 170902, Dms : 10057 Timer : 0, programmed : 5000, actual : 5000 Timer : 1, programmed : 10000, actual : 10000 Timer : 2, programmed : 15000, actual : 15000 Timer : 3, programmed : 20000, actual : 20000 Timer : 4, programmed : 25000, actual : 25000 Timer : 5, programmed : 30000, actual : 30000 Timer : 6, programmed : 35000, actual : 35000 Timer : 7, programmed : 40000, actual : 40000 Timer : 8, programmed : 45000, actual : 45000 Timer : 9, programmed : 50000, actual : 50000 Timer : 10, programmed : 55000, actual : 55000 Timer : 11, programmed : 60000, actual : 60000 Timer : 12, programmed : 65000, actual : 65000 Timer : 13, programmed : 70000, actual : 70000 Timer : 14, programmed : 75000, actual : 75000 Timer : 15, programmed : 80000, actual : 80000

Debug

Debug is enabled by default on Serial.

You can also change the debugging level (TIMERINTERRUPT_LOGLEVEL) from 0 to 4

// These define's must be placed at the beginning before #include "SAMDUE_TimerInterrupt.h" // _TIMERINTERRUPT_LOGLEVEL_ from 0 to 4 // Don't define _TIMERINTERRUPT_LOGLEVEL_ > 0. Only for special ISR debugging only. Can hang the system. #define TIMER_INTERRUPT_DEBUG 0 #define _TIMERINTERRUPT_LOGLEVEL_ 0

Troubleshooting

If you get compilation errors, more often than not, you may need to install a newer version of the core for Arduino boards.

Sometimes, the library will only work if you update the board core to the latest version because I am using newly added functions.

Issues

Submit issues to: SAMDUE_TimerInterrupt issues

TO DO

Search for bug and improvement.

DONE

Basic hardware timers for SAM DUE.
More hardware-initiated software-enabled timers
Longer time interval
Similar features for remaining Arduino boards such as ESP32, ESP8266, STM32, nRF52, mbed-nRF52, Teensy, etc.
Add Table of Contents
Fix multiple-definitions linker error
Optimize library code by using reference-passing instead of value-passing

Contributions and Thanks

Many thanks for everyone for bug reporting, new feature suggesting, testing and contributing to the development of this library.

Use some code from the Ivan Seidel's DueTimer Library.

_{⭐️ Ivan Seidel}

Contributing

If you want to contribute to this project:

Report bugs and errors
Ask for enhancements
Create issues and pull requests
Tell other people about this library

License

The library is licensed under MIT

Name		Name	Last commit message	Last commit date
Latest commit History 33 Commits
.github		.github
LibraryPatches		LibraryPatches
Packages_Patches/arduino/hardware/sam/1.6.12		Packages_Patches/arduino/hardware/sam/1.6.12
examples		examples
platformio		platformio
src		src
utils		utils
.codespellrc		.codespellrc
.gitignore		.gitignore
CONTRIBUTING.md		CONTRIBUTING.md
LICENSE		LICENSE
README.md		README.md
changelog.md		changelog.md
keywords.txt		keywords.txt
library.json		library.json
library.properties		library.properties

	#if !( defined(ARDUINO_SAM_DUE) \|\| defined(__SAM3X8E__) )
	#error This code is designed to run on SAM DUE board / platform! Please check your Tools->Board setting.
	#endif

	// These define's must be placed at the beginning before #include "SAMDUETimerInterrupt.h"
	// _TIMERINTERRUPT_LOGLEVEL_ from 0 to 4
	// Don't define _TIMERINTERRUPT_LOGLEVEL_ > 0. Only for special ISR debugging only. Can hang the system.
	// Don't define TIMER_INTERRUPT_DEBUG > 2. Only for special ISR debugging only. Can hang the system.
	#define TIMER_INTERRUPT_DEBUG 0
	#define _TIMERINTERRUPT_LOGLEVEL_ 3

	// To be included only in main(), .ino with setup() to avoid `Multiple Definitions` Linker Error
	#include "SAMDUETimerInterrupt.h"

	// To be included only in main(), .ino with setup() to avoid `Multiple Definitions` Linker Error
	#include "SAMDUE_ISR_Timer.h"

	#include <SimpleTimer.h> // https://github.com/jfturcot/SimpleTimer

	#ifndef LED_BUILTIN
	#define LED_BUILTIN 13
	#endif

	#ifndef LED_BLUE
	#define LED_BLUE 2
	#endif

	#ifndef LED_RED
	#define LED_RED 3
	#endif

	#define HW_TIMER_INTERVAL_US 10000L

	volatile uint32_t startMillis = 0;

	// Init SAMDUE_ISR_Timer
	// Each SAMDUE_ISR_Timer can service 16 different ISR-based timers
	SAMDUE_ISR_Timer ISR_Timer;

	#define LED_TOGGLE_INTERVAL_MS 2000L

	void TimerHandler()
	{
	static bool toggle = false;
	static int timeRun = 0;

	ISR_Timer.run();

	// Toggle LED every LED_TOGGLE_INTERVAL_MS = 2000ms = 2s
	if (++timeRun == ((LED_TOGGLE_INTERVAL_MS * 1000) / HW_TIMER_INTERVAL_US) )
	{
	timeRun = 0;

	//timer interrupt toggles pin LED_BUILTIN
	digitalWrite(LED_BUILTIN, toggle);
	toggle = !toggle;
	}
	}

	/////////////////////////////////////////////////

	#define NUMBER_ISR_TIMERS 16

	typedef void (*irqCallback) ();

	/////////////////////////////////////////////////

	#define USE_COMPLEX_STRUCT true

	#if USE_COMPLEX_STRUCT

	typedef struct
	{
	irqCallback irqCallbackFunc;
	uint32_t TimerInterval;
	unsigned long deltaMillis;
	unsigned long previousMillis;
	} ISRTimerData;

	// In NRF52, avoid doing something fancy in ISR, for example Serial.print()
	// The pure simple Serial.prints here are just for demonstration and testing. Must be eliminate in working environment
	// Or you can get this run-time error / crash

	void doingSomething(int index);

	#else

	volatile unsigned long deltaMillis [NUMBER_ISR_TIMERS] = { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 };
	volatile unsigned long previousMillis [NUMBER_ISR_TIMERS] = { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 };

	// You can assign any interval for any timer here, in milliseconds
	uint32_t TimerInterval[NUMBER_ISR_TIMERS] =
	{
	5000L, 10000L, 15000L, 20000L, 25000L, 30000L, 35000L, 40000L,
	45000L, 50000L, 55000L, 60000L, 65000L, 70000L, 75000L, 80000L
	};

	void doingSomething(int index)
	{
	unsigned long currentMillis = millis();

	deltaMillis[index] = currentMillis - previousMillis[index];
	previousMillis[index] = currentMillis;
	}

	#endif

	////////////////////////////////////
	// Shared
	////////////////////////////////////

	void doingSomething0()
	{
	doingSomething(0);
	}

	void doingSomething1()
	{
	doingSomething(1);
	}

	void doingSomething2()
	{
	doingSomething(2);
	}

	void doingSomething3()
	{
	doingSomething(3);
	}

	void doingSomething4()
	{
	doingSomething(4);
	}

	void doingSomething5()
	{
	doingSomething(5);
	}

	void doingSomething6()
	{
	doingSomething(6);
	}

	void doingSomething7()
	{
	doingSomething(7);
	}

	void doingSomething8()
	{
	doingSomething(8);
	}

	void doingSomething9()
	{
	doingSomething(9);
	}

	void doingSomething10()
	{
	doingSomething(10);
	}

	void doingSomething11()
	{
	doingSomething(11);
	}

	void doingSomething12()
	{
	doingSomething(12);
	}

	void doingSomething13()
	{
	doingSomething(13);
	}

	void doingSomething14()
	{
	doingSomething(14);
	}

	void doingSomething15()
	{
	doingSomething(15);
	}

	#if USE_COMPLEX_STRUCT

	ISRTimerData curISRTimerData[NUMBER_ISR_TIMERS] =
	{
	//irqCallbackFunc, TimerInterval, deltaMillis, previousMillis
	{ doingSomething0, 5000L, 0, 0 },
	{ doingSomething1, 10000L, 0, 0 },
	{ doingSomething2, 15000L, 0, 0 },
	{ doingSomething3, 20000L, 0, 0 },
	{ doingSomething4, 25000L, 0, 0 },
	{ doingSomething5, 30000L, 0, 0 },
	{ doingSomething6, 35000L, 0, 0 },
	{ doingSomething7, 40000L, 0, 0 },
	{ doingSomething8, 45000L, 0, 0 },
	{ doingSomething9, 50000L, 0, 0 },
	{ doingSomething10, 55000L, 0, 0 },
	{ doingSomething11, 60000L, 0, 0 },
	{ doingSomething12, 65000L, 0, 0 },
	{ doingSomething13, 70000L, 0, 0 },
	{ doingSomething14, 75000L, 0, 0 },
	{ doingSomething15, 80000L, 0, 0 }
	};

	void doingSomething(int index)
	{
	unsigned long currentMillis = millis();

	curISRTimerData[index].deltaMillis = currentMillis - curISRTimerData[index].previousMillis;
	curISRTimerData[index].previousMillis = currentMillis;
	}

	#else

	irqCallback irqCallbackFunc[NUMBER_ISR_TIMERS] =
	{
	doingSomething0, doingSomething1, doingSomething2, doingSomething3,
	doingSomething4, doingSomething5, doingSomething6, doingSomething7,
	doingSomething8, doingSomething9, doingSomething10, doingSomething11,
	doingSomething12, doingSomething13, doingSomething14, doingSomething15
	};

	#endif
	///////////////////////////////////////////

	#define SIMPLE_TIMER_MS 2000L

	// Init SimpleTimer
	SimpleTimer simpleTimer;

	// Here is software Timer, you can do somewhat fancy stuffs without many issues.
	// But always avoid
	// 1. Long delay() it just doing nothing and pain-without-gain wasting CPU power.Plan and design your code / strategy ahead
	// 2. Very long "do", "while", "for" loops without predetermined exit time.
	void simpleTimerDoingSomething2s()
	{
	static unsigned long previousMillis = startMillis;

	unsigned long currMillis = millis();

	Serial.print(F("SimpleTimer : "));Serial.print(SIMPLE_TIMER_MS / 1000);
	Serial.print(F(", ms : ")); Serial.print(currMillis);
	Serial.print(F(", Dms : ")); Serial.println(currMillis - previousMillis);

	for (uint16_t i = 0; i < NUMBER_ISR_TIMERS; i++)
	{
	#if USE_COMPLEX_STRUCT
	Serial.print(F("Timer : ")); Serial.print(i);
	Serial.print(F(", programmed : ")); Serial.print(curISRTimerData[i].TimerInterval);
	Serial.print(F(", actual : ")); Serial.println(curISRTimerData[i].deltaMillis);
	#else
	Serial.print(F("Timer : ")); Serial.print(i);
	Serial.print(F(", programmed : ")); Serial.print(TimerInterval[i]);
	Serial.print(F(", actual : ")); Serial.println(deltaMillis[i]);
	#endif
	}

	previousMillis = currMillis;
	}

	uint16_t attachDueInterrupt(double microseconds, timerCallback callback, const char* TimerName)
	{
	DueTimerInterrupt dueTimerInterrupt = DueTimer.getAvailable();

	dueTimerInterrupt.attachInterruptInterval(microseconds, callback);

	uint16_t timerNumber = dueTimerInterrupt.getTimerNumber();

	Serial.print(TimerName); Serial.print(F(" attached to Timer(")); Serial.print(timerNumber); Serial.println(F(")"));

	return timerNumber;
	}

	void setup()
	{
	pinMode(LED_BUILTIN, OUTPUT);

	Serial.begin(115200);
	while (!Serial);

	delay(100);

	Serial.print(F("\nStarting ISR_16_Timers_Array_Complex on ")); Serial.println(BOARD_NAME);
	Serial.println(SAMDUE_TIMER_INTERRUPT_VERSION);
	Serial.print(F("CPU Frequency = ")); Serial.print(F_CPU / 1000000); Serial.println(F(" MHz"));
	Serial.print(F("Timer Frequency = ")); Serial.print(SystemCoreClock / 1000000); Serial.println(F(" MHz"));

	// Interval in microsecs
	attachDueInterrupt(HW_TIMER_INTERVAL_US, TimerHandler, "ITimer");

	startMillis = millis();

	// Just to demonstrate, don't use too many ISR Timers if not absolutely necessary
	// You can use up to 16 timer for each ISR_Timer
	for (uint8_t i = 0; i < NUMBER_ISR_TIMERS; i++)
	{
	#if USE_COMPLEX_STRUCT
	curISRTimerData[i].previousMillis = startMillis;
	ISR_Timer.setInterval(curISRTimerData[i].TimerInterval, curISRTimerData[i].irqCallbackFunc);
	#else
	previousMillis[i] = startMillis;
	ISR_Timer.setInterval(TimerInterval[i], irqCallbackFunc[i]);
	#endif
	}

	// You need this timer for non-critical tasks. Avoid abusing ISR if not absolutely necessary.
	simpleTimer.setInterval(SIMPLE_TIMER_MS, simpleTimerDoingSomething2s);
	}

	#define BLOCKING_TIME_MS 10000L

	void loop()
	{
	// This unadvised blocking task is used to demonstrate the blocking effects onto the execution and accuracy to Software timer
	// You see the time elapse of ISR_Timer still accurate, whereas very unaccurate for Software Timer
	// The time elapse for 2000ms software timer now becomes 3000ms (BLOCKING_TIME_MS)
	// While that of ISR_Timer is still prefect.
	delay(BLOCKING_TIME_MS);

	// You need this Software timer for non-critical tasks. Avoid abusing ISR if not absolutely necessary
	// You don't need to and never call ISR_Timer.run() here in the loop(). It's already handled by ISR timer.
	simpleTimer.run();
	}

Uh oh!

License

Uh oh!

khoih-prog/SAMDUE_TimerInterrupt

Folders and files

Latest commit

History

Repository files navigation

SAMDUE_TimerInterrupt Library

Table of Contents

Important Change from v1.3.0

Why do we need this SAMDUE_TimerInterrupt library

Features

Why using ISR-based Hardware Timer Interrupt is better

Currently supported Boards

Important Notes about ISR

Prerequisites

Installation

Use Arduino Library Manager

Manual Install

VS Code & PlatformIO

Packages' Patches

1. For Arduino SAM DUE boards

Libraries' Patches

Notes: These patches are totally optional and necessary only when you use the related Ethernet library and get certain error or issues.

1. For application requiring 2K+ HTML page

2. For Ethernet library

3. For EthernetLarge library

4. For Ethernet2 library

5. For Ethernet3 library

6. For UIPEthernet library

7. For fixing ESP32 compile error

HOWTO Fix Multiple Definitions Linker Error

New from v1.0.1

Usage

1. Using only Hardware Timer directly

1.1 Init Hardware Timer

1.2 Set Hardware Timer Interval and attach Timer Interrupt Handler function

2. Using 16 ISR_based Timers from 1 Hardware Timer

2.1 Init Hardware Timer and ISR-based Timer

2.2 Set Hardware Timer Interval and attach Timer Interrupt Handler functions

Examples:

Example ISR_16_Timers_Array_Complex

Debug Terminal Output Samples

1. ISR_Timer_Complex_Ethernet on Arduino SAM DUE

2. TimerInterruptTest on Arduino SAM DUE

3. ISR_16_Timers_Array on Arduino SAM DUE

4. Change_Interval on Arduino SAM DUE

5. ISR_16_Timers_Array_Complex on Arduino SAM DUE

Debug

Troubleshooting

Issues

TO DO

DONE

Contributions and Thanks

Contributing

License

Copyright

About

Topics

Resources

License

Contributing

Uh oh!

Stars

Watchers

Forks

Releases 4

Packages 0

Languages

HOWTO Fix `Multiple Definitions` Linker Error

Packages