Hi wayne, here is the boot log.
[0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-8728f3cb) [0000.130] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.138] Power-up reason: pmc por [0000.141] No Battery Present [0000.144] pmic max77620 reset reason [0000.147] pmic max77620 NVERC : 0x40 [0000.151] RamCode = 0 [0000.153] Platform has DDR4 type RAM [0000.156] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x2d2d62 [0000.172] Entering ramdump check [0000.175] Get RamDumpCarveOut = 0x0 [0000.179] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.188] Sdram initialization is successful [0000.192] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.199] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.204] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.210] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.234] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.269] BoardID = 3448, SKU = 0x0 [0000.272] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.276] Nano-SD: checking PT table on QSPI ... [0000.281] Initialize FailControl [0000.284] Read PT from (2:0) [0000.314] PT crc32 and magic check passed. [0000.318] Using BFS PT to query partitions [0000.324] Loading Tboot-CPU binary [0000.352] Verifying TBC in OdmNonSecureSBK mode [0000.362] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.369] Bootloader downloaded successfully. [0000.373] Downloaded Tboot-CPU binary to 0xa0000258 [0000.378] MAX77620_GPIO5 configured [0000.381] CPU power rail is up [0000.384] CPU clock enabled [0000.388] Performing RAM repair [0000.391] Updating A64 Warmreset Address to 0xa00002e9 [0000.396] BoardID = 3448, SKU = 0x0 [0000.399] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.403] Nano-SD: checking PT table on QSPI ... [0000.407] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.413] Loading NvTbootBootloaderDTB [0000.480] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.551] Bootloader DTB Load Address: 0x83000000 [0000.556] BoardID = 3448, SKU = 0x0 [0000.559] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.563] Nano-SD: checking PT table on QSPI ... [0000.567] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.574] Loading NvTbootKernelDTB [0000.640] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.711] Kernel DTB Load Address: 0x83100000 [0000.715] BoardID = 3448, SKU = 0x0 [0000.718] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.722] Nano-SD: checking PT table on QSPI ... [0000.727] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.734] Loading cboot binary [0000.850] Verifying EBT in OdmNonSecureSBK mode [0000.892] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.899] Bootloader downloaded successfully. [0000.903] BoardID = 3448, SKU = 0x0 [0000.906] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.910] Nano-SD: checking PT table on QSPI ... [0000.914] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.921] PT: Partition NCT NOT found ! [0000.924] Warning: Find Partition via PT Failed [0000.929] Next binary entry address: 0x92c00258 [0000.933] BoardId: 3448 [0000.938] Overriding pmu board id with proc board id [0000.942] Display board id is not available [0000.947] BoardID = 3448, SKU = 0x0 [0000.950] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.954] Nano-SD: checking PT table on QSPI ... [0000.958] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.065] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.121] /bpmp deleted [0001.123] SC7EntryFw header found loaded at 0xff700000 [0001.311] OVR2 PMIC [0001.313] Bpmp FW successfully loaded [0001.316] BoardID = 3448, SKU = 0x0 [0001.320] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.323] Nano-SD: checking PT table on QSPI ... [0001.328] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.335] WB0 init successfully at 0xff780000 [0001.339] Verifying NvTbootWb0 in OdmNonSecureSBK mode [0001.344] Set NvDecSticky Bits [0001.348] GSC2 address ff53fffc value c0edbbcc [0001.354] GSC MC Settings done [0001.357] BoardID = 3448, SKU = 0x0 [0001.360] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.364] Nano-SD: checking PT table on QSPI ... [0001.368] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.375] TOS Image length 53680 [0001.378] Monitor size 53680 [0001.381] OS size 0 [0001.396] Secure Os AES-CMAC Verification Success! [0001.401] TOS image cipher info: plaintext [0001.405] Loading and Validation of Secure OS Successful [0001.421] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.425] NvTbootPackSdramParams: start. [0001.430] NvTbootPackSdramParams: done. [0001.434] Tegraboot started after 51868 us [0001.438] Basic modules init took 936020 us [0001.442] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB [0001.448] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.453] Next stage binary read took 102861 us [0001.458] Carveout took -132464 us [0001.461] CPU initialization took 510777 us [0001.465] Total time taken by TegraBoot 1417194 us [0001.470] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):b5eeb33 NOTICE: BL31: Built : 08:56:32, Feb 19 2022 ERROR: Error initializing runtime service trusty_fast [0001.591] RamCode = 0 [0001.596] LPDDR4 Training: Read DT: Number of tables = 2 [0001.601] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.614] EMC Training Successful [0001.617] 408000 not found in DVFS table [0001.623] RamCode = 0 [0001.627] DT Write: emc-table@204000 succeeded [0001.632] DT Write: emc-table@1600000 succeeded [0001.636] LPDDR4 Training: Write DT: Number of tables = 2 [0001.685] [0001.686] Debug Init done [0001.688] Marked DTB cacheable [0001.691] Bootloader DTB loaded at 0x83000000 [0001.696] Marked DTB cacheable [0001.699] Kernel DTB loaded at 0x83100000 [0001.703] DeviceTree Init done [0001.716] Pinmux applied successfully [0001.720] gicd_base: 0x50041000 [0001.724] gicc_base: 0x50042000 [0001.727] Interrupts Init done [0001.731] Using base:0x60005090 & irq:208 for tick-timer [0001.736] Using base:0x60005098 for delay-timer [0001.741] platform_init_timer: DONE [0001.744] Timer(tick) Init done [0001.748] osc freq = 38400 khz [0001.752] [0001.753] Welcome to L4T Cboot [0001.756] [0001.757] Cboot Version: 00.00.2018.01-t210-a2f2e4b8 [0001.762] calling constructors [0001.765] initializing heap [0001.767] initializing threads [0001.770] initializing timers [0001.773] creating bootstrap completion thread [0001.778] top of bootstrap2() [0001.780] CPU: ARM Cortex A57 [0001.783] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.788] initializing platform [0001.795] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.800] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.804] Macronix QSPI chip present [0001.808] SPI device register [0001.811] init boot device [0001.813] allocating memory for boot device(SPI) [0001.818] registering boot device [0001.836] QSPI bdev is already initialized [0001.840] Enable APE clock [0001.843] Un-powergate APE partition [0001.846] of_register: registering tegra_udc to of_hal [0001.851] of_register: registering inv20628-driver to of_hal [0001.857] of_register: registering ads1015-driver to of_hal [0001.863] of_register: registering lp8557-bl-driver to of_hal [0001.868] of_register: registering bq2419x_charger to of_hal [0001.874] of_register: registering bq27441_fuel_gauge to of_hal [0001.885] gpio framework initialized [0001.889] of_register: registering tca9539_gpio to of_hal [0001.894] of_register: registering tca9539_gpio to of_hal [0001.900] of_register: registering i2c_bus_driver to of_hal [0001.905] of_register: registering i2c_bus_driver to of_hal [0001.911] of_register: registering i2c_bus_driver to of_hal [0001.916] pmic framework initialized [0001.920] of_register: registering max77620_pmic to of_hal [0001.925] regulator framework initialized [0001.929] of_register: registering tps65132_bl_driver to of_hal [0001.935] initializing target [0001.941] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.949] board ID = D78, board SKU = 0 [0001.953] Skipping Z3! [0001.958] fixed regulator driver initialized [0001.975] initializing OF layer [0001.978] NCK carveout not present [0001.982] Skipping dts_overrides [0001.986] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.002] I2C Bus Init done [0002.005] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.015] I2C Bus Init done [0002.018] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.028] I2C Bus Init done [0002.031] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.041] I2C Bus Init done [0002.044] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.054] I2C Bus Init done [0002.057] of_children_init: Ops found for compatible string maxim,max77620 [0002.067] max77620_init using irq 118 [0002.072] register 'maxim,max77620' pmic [0002.076] gpio_driver_register: register 'max77620-gpio' driver [0002.082] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.093] I2C Bus Init done [0002.097] NCK carveout not present [0002.106] Find /i2c@7000c000's alias i2c0 [0002.110] get eeprom at 1-a0, size 256, type 0 [0002.119] Find /i2c@7000c500's alias i2c2 [0002.122] get eeprom at 3-a0, size 256, type 0 [0002.127] get eeprom at 3-ae, size 256, type 0 [0002.131] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.137] I2C slave not started [0002.140] I2C write failed [0002.142] Writing offset failed [0002.145] eeprom_init: EEPROM read failed [0002.149] pm_ids_update: eeprom init failed [0002.153] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.183] pm_ids_update: The pm board id is 3448-0000-401 [0002.190] Adding plugin-manager/ids/3448-0000-401=/i2c@7000c500:module@0x50 [0002.199] pm_ids_update: pm id update successful [0002.203] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.233] pm_ids_update: The pm board id is 3449-0000-400 [0002.239] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.247] pm_ids_update: pm id update successful [0002.278] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.284] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.291] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.297] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.306] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:5b:fb:44 [0002.312] Plugin Manager: Parse ODM data 0x000a4000 [0002.324] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x7 [0002.339] Find /i2c@7000c000's alias i2c0 [0002.343] get eeprom at 1-a0, size 256, type 0 [0002.351] Find /i2c@7000c500's alias i2c2 [0002.355] get eeprom at 3-a0, size 256, type 0 [0002.360] get eeprom at 3-ae, size 256, type 0 [0002.364] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.369] I2C slave not started [0002.372] I2C write failed [0002.375] Writing offset failed [0002.378] eeprom_init: EEPROM read failed [0002.382] pm_ids_update: eeprom init failed [0002.386] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.416] pm_ids_update: The pm board id is 3448-0000-401 [0002.422] Adding plugin-manager/ids/3448-0000-401=/i2c@7000c500:module@0x50 [0002.429] pm_ids_update: pm id update successful [0002.434] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.464] pm_ids_update: The pm board id is 3449-0000-400 [0002.470] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.477] pm_ids_update: pm id update successful [0002.508] Add serial number:1423221060513 as DT property [0002.515] Applying platform configs [0002.522] platform-init is not present. Skipping [0002.526] calling apps_init() [0002.532] Couldn't find GPT header [0002.537] Proceeding to Cold Boot [0002.540] starting app android_boot_app [0002.544] Device state: unlocked [0002.547] display console init [0002.555] could not find regulator [0002.558] hdmi cable connected [0002.574] edid read success [0002.589] edid read success [0002.592] widthDT entry for leds-pwm not found [0002.599] = 640, height = 480, frequency = 25174825 [0002.604] width = 640, height = 480, frequency = 25174825 [0002.610] width = 640, height = 480, frequency = 25174825 [0002.615] width = 640, height = 480, frequency = 25174825 [0002.620] width = 1920, height = 1080, frequency = 148500000 [0002.626] width = 1920, height = 1080, frequency = 138500000 [0002.632] width = 1920, height = 1080, frequency = 148351648 [0002.637] width = 1280, height = 720, frequency = 74175824 [0002.643] width = 720, height = 480, frequency = 26973026 [0002.648] width = 720, height = 480, frequency = 26973026 [0002.654] width = 640, height = 480, frequency = 25174825 [0002.659] width = 720, height = 576, frequency = 26973026 [0002.664] width = 720, height = 576, frequency = 26973026 [0002.670] width = 1280, height = 720, frequency = 74175824 [0002.675] width = 1920, height = 1080, frequency = 148351648 [0002.681] Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.689] tmds-config node not found [0002.693] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltageps [0002.707] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.715] could not find regulator [0002.718] could not find regulator [0002.722] could not find regulator [0002.750] using default cmu settings [0002.753] dc_hdmi_enable, starting HDMI initialisation [0002.760] dc_hdmi_enable, HDMI initialisation complete [0002.765] list and configure display window [0002.773] display console init completed [0002.784] subnode volume_up is not found ! [0002.788] subnode back is not found ! [0002.792] subnode volume_down is not found ! [0002.796] subnode menu is not found ! [0002.800] Gpio keyboard init success [0002.880] found decompressor handler: lz4-legacy [0002.895] decompressing blob (type 1)... [0002.965] load_bmp_blob: panelresolution=1080 type=3 [0002.970] -------> se_aes_verify_sbk_clear: 747 [0002.974] se_aes_verify_sbk_clear: Error [0002.978] SE operation failed [0002.981] bl_battery_charging: connected to external power supply [0002.993] device_query_partition_size: failed to open partition spiflash0:MSC ! [0003.000] MSC Partition not found [0003.006] device_query_partition_size: failed to open partition spiflash0:USP ! [0003.014] USP partition read failed! [0003.017] blob_init: blob-partition USP header read failed [0003.023] android_boot Unable to update recovery partition [0003.028] kfs_getpartname: name = LNX [0003.032] Loading kernel from LNX [0003.041] Found 19 BFS partitions in "spiflash0" [0003.363] load kernel from storage [0003.368] decompressor handler not found [0003.634] Successfully loaded kernel and ramdisk images [0003.639] board ID = D78, board SKU = 0 [0003.644] sdmmc node status = okay [0003.647] sdcard instance = 0 [0003.650] sdmmc cd-inverted [0003.653] sdcard gpio handle 0x5b [0003.656] sdcard gpio pin 0xc9 [0003.659] sdcard gpio flags 0x0 [0003.662] vmmc-supply 0x9d [0003.665] cd_gpio_pin = 201 [0003.667] pin_state = 0 [0003.670] Found sdcard [0003.672] SD-card IS present ... [0003.675] load_and_boot_kernel: SD card detected OK [0003.681] load_bmp_blob: panelresolution=1080 type=3 [0004.175] display bmp image done [0004.178] NCK carveout not present [0004.181] Skipping dts_overrides [0004.184] NCK carveout not present [0004.194] Find /i2c@7000c000's alias i2c0 [0004.198] get eeprom at 1-a0, size 256, type 0 [0004.206] Find /i2c@7000c500's alias i2c2 [0004.210] get eeprom at 3-a0, size 256, type 0 [0004.215] get eeprom at 3-ae, size 256, type 0 [0004.219] pm_ids_update: Updating 1,a0, size 256, type 0 [0004.224] I2C slave not started [0004.227] I2C write failed [0004.230] Writing offset failed [0004.233] eeprom_init: EEPROM read failed [0004.237] pm_ids_update: eeprom init failed [0004.241] pm_ids_update: Updating 3,a0, size 256, type 0 [0004.271] pm_ids_update: The pm board id is 3448-0000-401 [0004.278] Adding plugin-manager/ids/3448-0000-401=/i2c@7000c500:module@0x50 [0004.287] pm_ids_update: pm id update successful [0004.291] pm_ids_update: Updating 3,ae, size 256, type 0 [0004.321] pm_ids_update: The pm board id is 3449-0000-400 [0004.327] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0004.335] pm_ids_update: pm id update successful [0004.366] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.371] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0004.379] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.385] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0004.393] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:5b:fb:44 [0004.400] Plugin Manager: Parse ODM data 0x000a4000 [0004.412] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x7 [0004.421] Add serial number:1423221060513 as DT property [0004.430] "bpmp" doesn't exist, creating [0004.435] Updated bpmp info to DTB [0004.440] Updated initrd info to DTB [0004.443] "proc-board" doesn't exist, creating [0004.449] Updated board info to DTB [0004.453] "pmu-board" doesn't exist, creating [0004.459] Updated board info to DTB [0004.462] "display-board" doesn't exist, creating [0004.468] Updated board info to DTB [0004.471] "reset" doesn't exist, creating [0004.476] Updated reset info to DTB [0004.479] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype [0004.519] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0004.524] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 [0004.538] Updated bootarg info to DTB [0004.542] Adding uuid 00000001643073070000000003010040 to DT [0004.548] Adding eks info 0 to DT [0004.554] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0004.560] Updated memory info to DTB [0004.567] set vdd_core voltage to 1075 mv [0004.571] setting 'vdd-core' regulator to 1075000 micro volts [0004.577] Found secure-pmc; disable BPMP U-Boot 2020.04-g4335beb (Feb 19 2022 - 08:56:35 -0800) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 25B *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 845 bytes read in 28 ms (29.3 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 7160133 bytes read in 333 ms (20.5 MiB/s) Retrieving file: /boot/Image 34484232 bytes read in 1508 ms (21.8 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resiz ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083100000, end 000000008317ced3 copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.253-tegra (buildbrain@mobile-u64-5496-d5000) (1 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 1.164826] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.359661] imx219 7-0010: imx219_board_setup: error during i2c read probe () [ 1.359793] imx219 7-0010: board setup failed [ 1.384035] imx219 8-0010: imx219_board_setup: error during i2c read probe () [ 1.384116] imx219 8-0010: board setup failed [ 2.737980] cgroup: cgroup2: unknown option "nsdelegate" [ 3.890934] using random self ethernet address [ 3.897644] using random host ethernet address [ 4.300627] random: crng init done [ 4.304058] random: 7 urandom warning(s) missed due to ratelimiting [ 4.596944] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-26.u2 [ 4.607945] iwlwifi 0000:01:00.0: Falling back to user helper [ 5.116828] using random self ethernet address [ 5.124645] using random host ethernet address [ 5.358536] uvcvideo 2-1.4:1.0: Entity type for entity Intel(R) RealSense(TM! [ 5.376054] uvcvideo 2-1.4:1.0: Entity type for entity Processing 2 was not ! [ 5.386167] uvcvideo 2-1.4:1.0: Entity type for entity Camera 1 was not init! [ 5.401935] uvcvideo 2-1.4:1.3: Entity type for entity Processing 7 was not ! [ 5.474967] uvcvideo 2-1.4:1.3: Entity type for entity Extension 8 was not i! [ 5.484281] uvcvideo 2-1.4:1.3: Entity type for entity Camera 6 was not init! [ 6.145265] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-25.u2 [ 6.155511] iwlwifi 0000:01:00.0: Falling back to user helper [ 6.797519] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-24.u2 [ 6.807499] iwlwifi 0000:01:00.0: Falling back to user helper [ 6.969487] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-23.u2 [ 6.981017] iwlwifi 0000:01:00.0: Falling back to user helper [ 7.261397] thermal thermal_zone6: failed to read out thermal zone (-5) [ 8.140367] Bridge firewalling registered
