Support multiple devices and platforms.

Patched in changes from Paul Stoffregen (http://www.pjrc.com/teensy/td_libs_IRremote.html)

Author: shirriff

IRremote.cpp

@@ -4,6 +4,8 @@
  * Copyright 2009 Ken Shirriff
  * For details, see http://arcfn.com/2009/08/multi-protocol-infrared-remote-library.html
  *
+ * Modified by Paul Stoffregen <paul@pjrc.com> to support other boards and timers
+ *
  * Interrupt code based on NECIRrcv by Joe Knapp
  * http://www.arduino.cc/cgi-bin/yabb2/YaBB.pl?num=1210243556
  * Also influenced by http://zovirl.com/2008/11/12/building-a-universal-remote-with-an-arduino/
@@ -169,15 +171,15 @@ void IRsend::sendRC6(unsigned long data, int nbits)
 void IRsend::mark(int time) {
  // Sends an IR mark for the specified number of microseconds.
  // The mark output is modulated at the PWM frequency.
- TCCR2A |= _BV(COM2B1); // Enable pin 3 PWM output
+ TIMER_ENABLE_PWM; // Enable pin 3 PWM output
  delayMicroseconds(time);
 }
 
 /* Leave pin off for time (given in microseconds) */
 void IRsend::space(int time) {
  // Sends an IR space for the specified number of microseconds.
  // A space is no output, so the PWM output is disabled.
- TCCR2A &= ~(_BV(COM2B1)); // Disable pin 3 PWM output
+ TIMER_DISABLE_PWM; // Disable pin 3 PWM output
  delayMicroseconds(time);
 }
 
@@ -195,21 +197,17 @@ void IRsend::enableIROut(int khz) {
 
 
  // Disable the Timer2 Interrupt (which is used for receiving IR)
- TIMSK2 &= ~_BV(TOIE2); //Timer2 Overflow Interrupt
+ TIMER_DISABLE_INTR; //Timer2 Overflow Interrupt
 
- pinMode(3, OUTPUT);
- digitalWrite(3, LOW); // When not sending PWM, we want it low
+ pinMode(TIMER_PWM_PIN, OUTPUT);
+ digitalWrite(TIMER_PWM_PIN, LOW); // When not sending PWM, we want it low
 
  // COM2A = 00: disconnect OC2A
  // COM2B = 00: disconnect OC2B; to send signal set to 10: OC2B non-inverted
  // WGM2 = 101: phase-correct PWM with OCRA as top
  // CS2 = 000: no prescaling
- TCCR2A = _BV(WGM20);
- TCCR2B = _BV(WGM22) | _BV(CS20);
-
  // The top value for the timer. The modulation frequency will be SYSCLOCK / 2 / OCR2A.
- OCR2A = SYSCLOCK / 2 / khz / 1000;
- OCR2B = OCR2A / 3; // 33% duty cycle
+ TIMER_CONFIG_KHZ(khz);
 }
 
 IRrecv::IRrecv(int recvpin)
@@ -220,28 +218,24 @@ IRrecv::IRrecv(int recvpin)
 
 // initialization
 void IRrecv::enableIRIn() {
+ cli();
  // setup pulse clock timer interrupt
- TCCR2A = 0; // normal mode
-
  //Prescale /8 (16M/8 = 0.5 microseconds per tick)
  // Therefore, the timer interval can range from 0.5 to 128 microseconds
  // depending on the reset value (255 to 0)
- cbi(TCCR2B,CS22);
- sbi(TCCR2B,CS21);
- cbi(TCCR2B,CS20);
+ TIMER_CONFIG_NORMAL();
 
  //Timer2 Overflow Interrupt Enable
- sbi(TIMSK2,TOIE2);
+ TIMER_ENABLE_INTR;
 
- RESET_TIMER2;
+ TIMER_RESET;
 
  sei(); // enable interrupts
 
  // initialize state machine variables
  irparams.rcvstate = STATE_IDLE;
  irparams.rawlen = 0;
 
-
  // set pin modes
  pinMode(irparams.recvpin, INPUT);
 }
@@ -261,9 +255,9 @@ void IRrecv::blink13(int blinkflag)
 // First entry is the SPACE between transmissions.
 // As soon as a SPACE gets long, ready is set, state switches to IDLE, timing of SPACE continues.
 // As soon as first MARK arrives, gap width is recorded, ready is cleared, and new logging starts
-ISR(TIMER2_OVF_vect)
+ISR(TIMER_INTR_NAME)
 {
- RESET_TIMER2;
+ TIMER_RESET;
 
  uint8_t irdata = (uint8_t)digitalRead(irparams.recvpin);
 
@@ -320,10 +314,10 @@ ISR(TIMER2_OVF_vect)
 
  if (irparams.blinkflag) {
  if (irdata == MARK) {
- PORTB |= B00100000; // turn pin 13 LED on
+ BLINKLED_ON(); // turn pin 13 LED on
  } 
  else {
- PORTB &= B11011111; // turn pin 13 LED off
+ BLINKLED_OFF(); // turn pin 13 LED off
  }
  }
 }